閱讀 | 訂閱
閱讀 | 訂閱
今日要聞

激光雕刻機清掃底部不平是什么原因?怎么解決?

cici 來源:百飛服務2018-04-16 我要評論(0 )   

激光雕刻機的應用非常廣泛,尤其在工藝禮品行業備受客戶青睞,不少客戶都靠著激光雕刻機賺了第一桶金,發家致了富。但機器也像人

 激光雕刻機的應用非常廣泛,尤其在工藝禮品行業備受客戶青睞,不少客戶都靠著激光雕刻機賺了第一桶金,發家致了富。但機器也像人一樣,隨著使用時間的增長,零部件的磨損等,機器會出現各種各樣的毛病。激光雕刻機也是如此,它可能會出現清掃底部不平等現象。那么,具體是什么原因?qū)е碌窨虣C(jī)出現清掃底部不平故障現象?自己又該怎么解決呢?小編今天整理以下資料供大家參考。

The application of laser engraving machine is very extensive, especially in the craft gift industry favored by customers, many customers rely on the laser engraving machine to make the first pot of gold, made a fortune. However, machines are also like people. With the increase in the use of time, the wear of parts, etc., the machine will have a variety of problems. The same is true of laser engraving machines, which may appear to sweep the bottom inequality. So, what are the specific reasons that cause the engraving machine to clean the bottom of the uneven phenomenon? How can I solve it myself? Xiaobian arranges the following information for your reference today.

 

激光雕刻機清掃底部不平是常見故障之一,表現為清掃時底部有明顯的突起現象,陰雕時表象為橫豎交叉處有明顯的不平整現象;陽雕時,在有字與無字間有明顯的突起橫線,清掃越深,現象越明顯。

Cleaning the bottom of the laser engraving machine is not one of the common faults. It shows that there are obvious protrusions at the bottom of the sweeping, and there are obvious irregularities in the horizontal and vertical intersections during the negative carving; in the case of Yangdiao, there are between the words and the non-words. Obviously protruding lines, the deeper the sweep, the more obvious the phenomenon.

故障原因

引起清掃不平的故障原因如下:

The cause of the failure of cleaning is as follows:

 

1、加工速度太快,激光管響應速度跟不上。  

1, the processing speed is too fast, laser tube response speed can not keep up.

2、吹氣流量不對,引起加工粉末粘連,形成橫線突起。

2. Insufficient blowing flow causes adhesion of the processing powder to form horizontal protrusions.

3、光路偏或焦距不對,產生散射光束,引起底部不平。  

3, Optical path deviation or focal length is wrong, resulting in scattered light beam, causing the bottom of the uneven.

4、聚焦鏡片選擇不合理,應盡量選擇短焦距鏡片,提高光束質量。

4, The choice of focusing lens is not reasonable, should try to choose short focal length lens, improve beam quality.

5、激光電源出光不穩。

5, Laser power supply instability.

 

解決

方法

清掃不平排除解決方法如下:  

Sweep up and remove the solution as follows:

 

1、首先檢查光路,保證光路正確。

1, First check the light path to ensure that the optical path is correct.

2、降低加工速度。

2, Reduce the processing speed.

3、調節好吹氣的氣量,保證無粉沫粘連。

3, Adjust the amount of blowing gas, to ensure that no powder adhesion.

4、選用短焦距鏡片,焦距調節應考慮被加工的深度。

4. Use short-focus lenses. Focus adjustment should take into account the depth of processing.

5、更換激光電源測試。

5, Replace the laser power test.

轉載請注明出處。

激光雕刻機機器
免責聲明

① 凡本網未注明其他出處的作品,版權均屬于激光制造網,未經本網授權不得轉載、摘編或利用其它方式使用。獲本網授權使用作品的,應在授權范圍內使 用,并注明"來源:激光制造網”。違反上述聲明者,本網將追究其相關責任。
② 凡本網注明其他來源的作品及圖片,均轉載自其它媒體,轉載目的在于傳遞更多信息,并不代表本媒贊同其觀點和對其真實性負責,版權歸原作者所有,如有侵權請聯系我們刪除。
③ 任何單位或個人認為本網內容可能涉嫌侵犯其合法權益,請及時向本網提出書面權利通知,并提供身份證明、權屬證明、具體鏈接(URL)及詳細侵權情況證明。本網在收到上述法律文件后,將會依法盡快移除相關涉嫌侵權的內容。

網友點評
0相關評論
精彩導讀